M-audio OmniStudio USB Manual de usuario Pagina 8

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 45
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 7
and 4 are monitored as a L/R stereo pair.
1
1
3
3
.
.
D
D
i
i
r
r
e
e
c
c
t
t
M
M
o
o
n
n
i
i
t
t
o
o
r
r
L
L
e
e
v
v
e
e
l
l
4
4
– With Direct Monitor Enable 3 and 4 switch in the IN position, this knob controls the level of audio from input 4
which is sent to the Direct Monitor bus.
1
1
4
4
.
.
H
H
e
e
a
a
d
d
p
p
h
h
o
o
n
n
e
e
1
1
a
a
n
n
d
d
2
2
L
L
e
e
v
v
e
e
l
l
s
s
– These knobs control the individual output levels of their respective headphone jacks.
1
1
5
5
.
.
H
H
e
e
a
a
d
d
p
p
h
h
o
o
n
n
e
e
1
1
a
a
n
n
d
d
2
2
O
O
u
u
t
t
p
p
u
u
t
t
s
s
– Each of these output jacks accepts a standard 1/4” stereo TRS headphone connector. The program
signal is the signal being sent to the Monitor (output) bus, and is identical on both headphone outputs, with individual levels regulated by
the associated Headphone Level Controls.
1
1
6
6
.
.
F
F
X
X
S
S
e
e
n
n
d
d
L
L
e
e
v
v
e
e
l
l
s
s
1
1
-
-
4
4
– These knobs control the FX Send levels from the four inputs, as sent to the rear panel FX Send output.
1
1
7
7
.
.
M
M
a
a
i
i
n
n
O
O
u
u
t
t
p
p
u
u
t
t
S
S
i
i
g
g
n
n
a
a
l
l
L
L
E
E
D
D
s
s
– When lit, these LEDs indicate the presence of an output signal greater than –15 dBFS on the OmniStudio USB’s
main output bus.
1
1
8
8
.
.
M
M
a
a
i
i
n
n
O
O
u
u
t
t
p
p
u
u
t
t
C
C
l
l
i
i
p
p
L
L
E
E
D
D
s
s
– When lit, these LEDs indicate the presence of too “hot” an audio signal (greater than -1 dBFS) on the OmniStudio
USB’s main output bus.
1
1
9
9
.
.
M
M
o
o
n
n
i
i
t
t
o
o
r
r
L
L
e
e
v
v
e
e
l
l
– This knob controls the output level to the OmniStudio USB’s rear panel Monitor Outputs.
2
2
0
0
.
.
P
P
h
h
a
a
n
n
t
t
o
o
m
m
P
P
o
o
w
w
e
e
r
r
S
S
w
w
i
i
t
t
c
c
h
h
– Pressing and engaging this switch in the IN position activates +48V phantom power to the two XLR Mic/Inst
Inputs. Phantom power is required for most condenser microphones.
2
2
1
1
.
.
P
P
h
h
a
a
n
n
t
t
o
o
m
m
P
P
o
o
w
w
e
e
r
r
L
L
E
E
D
D
– When lit, this LED indicates that phantom power is enabled.
2
2
2
2
.
.
P
P
o
o
w
w
e
e
r
r
L
L
E
E
D
D
– This LED indicates that the OmniStudio USB is connected and powered on. It does NOT indicate a valid USB connection to
a host computer.
2
2
3
3
.
.
P
P
o
o
w
w
e
e
r
r
S
S
w
w
i
i
t
t
c
c
h
h
– Pressing this switch will power on the OmniStudio USB and light the adjacent Power LED.
Rear Panel
2
2
4
4
.
.
P
P
o
o
w
w
e
e
r
r
C
C
o
o
n
n
n
n
e
e
c
c
t
t
o
o
r
r
– Connect the OmniStudio USB’s 9VAC 1A power supply to this input. Connect only the power supply provided with
the OmniStudio USB, or a power supply with an equivalent value.
NOTE: While most modern dynamic microphones are unaffected by phantom power, many ribbon mics and some older
dynamic microphones may be damaged if phantom power is applied to them.
7
Vista de pagina 7
1 2 3 4 5 6 7 8 9 10 11 12 13 ... 44 45

Comentarios a estos manuales

Sin comentarios